I Like Big Buttons! – Fabric Cover Buttons – Easy To Make, Great Impact!

cover-buttons-slide-show-pic_with-words_1

These aren’t your grandma’s Cover Buttons!!! Well actually they are 😉 only better, with so many many great uses for them.

Flat Backs are used for crafts were you would like to glue a cover button: jewelry, bracelets, rings, earrings, necklaces, bobby pins and barrettes, scrap booking, and much more.

Wire Backs are used for fabric cover buttons in sewing, shoes, clothing, pony tail holders and much, much more.

Here are the 7 sizes we carry. From 1/2″, which is about as small as your pinky nail, all the way up to 1 7/8″ in diameter, about the size of the round side of a kiwi fruit. We carry them in both flat back (glueable) and wire back (sewable).

Assembling fabric Cover Buttons is fast and simple. In just seconds, you will have a button ready for your latest craft project.

See our pictorial below:

How to Make Fabric Cover Buttons:

Cover Buttons are easy to assemble:

  1. Cut your fabric scrap. You will want a circle that is about twice the diameter of your button blank.
  2. Put your fabric piece in the larger assembly tool piece (RIGHT SIDE DOWN). When you look into the tool you want to see the back of the fabric.
  3. Place the button front (the domed piece) on top of the fabric. Leave the fabric edges hanging out.
  4. Press the cover button edges down into the tool.
  5. Place the back cover button piece on top of your fabric and button front. If the cover button will be subject to repeated tugging from the back, you may want to add a little e6000 adhesive before attaching the back.
  6. Take the smaller piece of the assembly tool and with the open side down place it on the button back.
  7. Press down. You may hear a pop when the last bit of the button back slips into place. If you take the tool out and the button is not completely secured, just put it back in and press down again.
  8. When you take the small assembly tool piece off, the fabric edges will be secured underneath the button back.
  9. Remove the button from the larger assembly tool piece.
  10. Tada!

To see other great Fabric Cover Button ideas, visit our DIY Project section here.

© ILikeBigButtons.com and I Like Big Buttons Blog, 2017.

Save

Save

Bandana Bib with KAM Snaps and a PDF Pattern by I Like Big Buttons!

Bandana Bib with KAM Snaps pic15

One of our most popular tutorials, Bandana Bibs are a great gift for those little droolers and mess makers in your life or as an outfit accessory. So cute!  I, also, used our Heart Shaped KAM Snaps for added pizazz, check it out!

Supplies:

Bandana Bib with KAM Snaps pic1

Instructions:

1.  Download the Bandana Bib PDF Pattern.  Print out the pattern making sure the 1″ square in the corner measures 1″ square when printed that will indicate the pattern is the right size.

Bandana Bib with KAM Snaps pic2

2.  Cut out the pattern.

Bandana Bib with KAM Snaps pic3

3.  Place your pattern, with long straight side on fabric folded in half, and pin in place.

Bandana Bib with KAM Snaps pic4

4.  Cut the 2 pieces of Fabric you will use.

Bandana Bib with KAM Snaps pic5

5.  Place Fabrics right sides together.

Bandana Bib with KAM Snaps pic6

6.  Pin together.

Bandana Bib with KAM Snaps pic7

7.  Sew pieces together with a 1/4″ seam allowance, back stitching at the start  and finish of sewing, make sure to leave a 3-4″ gap so that you can pull the piece right side out.

Bandana Bib with KAM Snaps pic8

8.  Pull piece right side out and make sure to push all the round and square corners out until they lay flat.

Bandana Bib with KAM Snaps pic9

9.  Fold in the opening’s seams and pin in place.

Bandana Bib with KAM Snaps pic10

10.  Stitch a finish stitch 1/8″ to 1/4″ all the way around the bib, making sure to ease your way around the left and right tabs.  I do a couple stitches, stop, then lift the foot, turn the fabric slightly, put the foot down, and do a couple more stitches and repeat.  Make sure the back stitch at the beginning and end of your sewing.

Bandana Bib with KAM Snaps pic11

11.  Use the template to mark the KAM Snap placement, you many want to check the measurement of your child’s neck and adjust the pattern or snap placement accordingly.  This bib worked for a toddler but with an extra set of snaps can work for more sizes.

Bandana Bib with KAM Snaps pic12

12.  I decided as I was getting ready to install the KAM Snaps to go with our new Heart Shaped snaps.  Install the Heart Shaped KAM Snap Cap and Stud in the left and a Cap and Socket on the right tab.

Bandana Bib with KAM Snaps pic14

13.  Interested in Heart Shaped KAM Snaps, check out our great 25 colors, in smaller package quantities for more great variety!

Bandana Bib with KAM Snaps pic15

14.  Totally cute, don’t you think! 😉 Happy Snapping!!!

One of our most popular tutorials, Bandana Bibs are a great gift for those little droolers and mess makers in your life or as an outfit accessory. So cute!  I, also, used our Heart Shaped KAM Snaps for added pizazz, check it out!

Supplies:

Bandana Bib with KAM Snaps pic1

Instructions:

1.  Download the Bandana Bib PDF Pattern.  Print out the pattern making sure the 1″ square in the corner measures 1″ square when printed that will indicate the pattern is the right size.

Bandana Bib with KAM Snaps pic2

2.  Cut out the pattern.

Bandana Bib with KAM Snaps pic3

3.  Place your pattern, with long straight side on fabric folded in half, and pin in place.

Bandana Bib with KAM Snaps pic4

4.  Cut the 2 pieces of Fabric you will use.

Bandana Bib with KAM Snaps pic5

5.  Place Fabrics right sides together.

Bandana Bib with KAM Snaps pic6

6.  Pin together.

Bandana Bib with KAM Snaps pic7

7.  Sew pieces together with a 1/4″ seam allowance, back stitching at the start  and finish of sewing, make sure to leave a 3-4″ gap so that you can pull the piece right side out.

Bandana Bib with KAM Snaps pic8

8.  Pull piece right side out and make sure to push all the round and square corners out until they lay flat.

Bandana Bib with KAM Snaps pic9

9.  Fold in the opening’s seams and pin in place.

Bandana Bib with KAM Snaps pic10

10.  Stitch a finish stitch 1/8″ to 1/4″ all the way around the bib, making sure to ease your way around the left and right tabs.  I do a couple stitches, stop, then lift the foot, turn the fabric slightly, put the foot down, and do a couple more stitches and repeat.  Make sure the back stitch at the beginning and end of your sewing.

Bandana Bib with KAM Snaps pic11

11.  Use the template to mark the KAM Snap placement, you many want to check the measurement of your child’s neck and adjust the pattern or snap placement accordingly.  This bib worked for a toddler but with an extra set of snaps can work for more sizes.

Bandana Bib with KAM Snaps pic12

12.  I decided as I was getting ready to install the KAM Snaps to go with our new Heart Shaped snaps.  Install the Heart Shaped KAM Snap Cap and Stud in the left and a Cap and Socket on the right tab.

Bandana Bib with KAM Snaps pic14

13.  Interested in Heart Shaped KAM Snaps, check out our great 25 colors, in smaller package quantities for more great variety!

Bandana Bib with KAM Snaps pic15

14.  Totally cute, don’t you think! 😉 Happy Snapping!!!

© ILikeBigButtons.com and I Like Big Buttons Blog, 2017.

Save

Save

Fabric Key Fob Hardware Wristlet Tutorial by I Like Big Buttons!

Before we get started, just a quick reminder:

I Like Big Buttons! – May The 4th Be With You Giveaway is still going on!!!

LINK TO GIVEAWAY

4 Prizes and 4 Winners:

1st Prize: Mint Professional KAM Plastic Snap Press with Size 20 Dies
2nd Prize: Key Fob Hardware Starter Kit
3rd Prize: Fabric Cover Button Bobby Pin and Barrette Starter Kit
4th Prize: 25 Random Mix of Enamel Clips

Giveaway Rules:

1. LIKE & SHARE this Giveaway, then COMMENT and share with us your favorite Star Wars character. In our house, there are too many to count. At the moment, I favor Princess Leia. She had the best hairdos and still managed to give the Empire what for. Who doesn’t like a strong female lead :).

2. Join our I Like Big Buttons! Group.

Also, if you don’t want to wait, you can get 10% off our website using Coupon Code: MAY4THBEWITHU

**Names will be drawn randomly with our Rafflecopter App ( https://ilikebigbuttons.com/blogs/news/444444 ). The first name drawn will receive the 1st prize, the second name drawn the 2nd prize, and so on.

💜💙💚💛❤️💜💙💚💛❤️💜💙💚💛❤️💜💙💚💛❤️💜💙💚💛❤️💜💙💚💛❤️💜💙💚💛❤️💜💙💚💛

Key Fob Hardware are some of our most popular craft supplies. Key Fob Hardware is simple to use and produces amazing results.  Just add your fabric, ribbon, or webbing for an instant, elegant wristlet.

Fabric Key Fob Hardware Wristlet Tutorial by I Like Big Buttons!

Supplies:

fabric-wristlet-tutorial-title-pic

Instructions:

1.  Cut a 10″ x 5″ section of Fabric of your choosing and 10″ x 2.5″ Fusible Fleece.

fabric-wristlet-tutorial-pic-2

2.  Iron Fusible Fleece to the center of the fabric.  Fold and iron the Fabric in half with the wrong sides together.

fabric-wristlet-tutorial-pic-4

3.  Unfold and iron the Fabric in half again long sides to the center.

fabric-wristlet-tutorial-pic-5

4.  It will look like this when you get done.

fabric-wristlet-tutorial-pic-6

5.  Use your Sewing Clips to pin the Wristlet flat.

fabric-wristlet-tutorial-pic-7

6.  Stitch along the edge of your Fabric strip, I stitched 1/4″ in.  Remove the Sewing Clips as you go.  Work slowly, keeping close to the edge and as straight of a line as possible.

fabric-wristlet-tutorial-pic-8

7.  Repeat 1/4″ stitching along the opposing edge.

fabric-wristlet-tutorial-pic-9

8.  Fold the Fabric Wristlet Strip in half, right sides facing out and match up the ends.

9. Stitch the ends together with a zig zag stitch.  I went back and forth a few times to insure it held.

10.  Trim any loose threads.  Use Fray Check to seal the end of the exposed Fabric edge.

fabric-wristlet-tutorial-pic-10

11.  Tuck the sewn seam ends into the Key Fob Hardware, making sure that the Fabric Wristlet is centered.

fabric-wristlet-tutorial-pic-11

12.  Using Key Fob Hardware Pliers squeeze the Key Fob Hardware closed with gentle pressure.  Sometimes, I go back and forth from left to right added a little bit of pressure to each side until it eases together.  Our Key Fob Hardware Pliers make this easy to do.

13.  Note the adjustable screw set to the distance I want the pliers to go to.

fabric-wristlet-tutorial-pic-13

14.  Add the Split Ring and Yay!!!

fabric-wristlet-tutorial-pic-14

15.  I love them and now I have a few sets to share!!!

To see all our Key Fob Hardware Tutorials, visit our Projects section here.

© ILikeBigButtons.com and I Like Big Buttons Blog, 2017.

Save

I Like Big Buttons! – May The 4th Be With You Giveaway!!!

Here at I Like Big Buttons! we are HUGE Star Wars fans. In celebration of that fun fact, we are running a super Star Wars giveaway to celebrate May the 4th. We will be giving away four (4) prizes, that means we will have four (4) lucky winners**! Details Below.

1st Prize:

2nd Prize:

3rd Prize:

4th Prize:

— GIVEAWAY DETAILS —

Giveaway good until Monday 05/15/2017

a Rafflecopter giveaway

ENTER TO WIN HERE (by Liking, Commenting, and Sharing our Facebook Post for this Giveaway):

Giveaway Rules:

1. LIKE & SHARE this Giveaway, then COMMENT and share with us your favorite Star Wars character. In our house, there are too many to count. At the moment, I favor Princess Leia. She had the best hairdos and still managed to give the Empire what for. Who doesn’t like a strong female lead :).

2. Join our I Like Big Buttons! Group.

*If your name is drawn as the winner, we will check to make sure you have completed all 3 requirements above.

Also, if you don’t want to wait, you can get 10% off our website using Coupon Code: MAY4THBEWITHU

**Names will be drawn randomly with our Rafflecopter App. The first name drawn will receive the 1st prize, the second name drawn the 2nd prize, and so on.

© ILikeBigButtons.com and I Like Big Buttons Blog, 2017.

Save

Save

Save

Save

Save

I Like Big Buttons! – How To Make A Fabric Cover Button Mini Clothespin

Today, I made an adorable office or home accent: Fabric Cover Button Mini Clothespins. I am absolutely in love with their bright colors and tininess!

Supplies:

  • 1 Completed Flat Back Fabric Cover Button (Attach size 20 (1/2″ / 12 mm), size 24 (5/8″ / 15 mm), or size 30 (3/4″ / 19 mm) flat back cover buttons.)
  • 1x Mini Wooden Clothespin (Approximately 1 3/8″ x 1/4″ in size)
  • 1x Small Plain Button
  • E6000, Hot Glue, or comparable adhesive

I Like Big Buttons! – How To Make Fabric Cover Button Mini Clothespins Video

I Like Big Buttons! – Picture Tutorial Below:

1.  Cut your fabric scrap. You will want a circle that is about twice the diameter of your button blank.

2.  Put your fabric piece in the larger assembly tool piece (RIGHT SIDE DOWN). When you look into the tool you want to see the back of the fabric.

3.  Place the button front (the domed piece) on top of the fabric. Leave the fabric edges hanging out.

4.  Press the cover button edges down into the tool. *TIP* To make it easier on my fingers, I use a sharpie marker to apply pressure.

5.  Place the back cover button piece on top of your fabric and button front. *TIP* If the cover button will be subject to repeated tugging from the back, you may want to add a little e6000 adhesive before attaching the back.

6.  Take the smaller piece of the assembly tool and with the open side down place it on the button back.

7.  Press down. You may hear a pop when the last bit of the button back slips into place. If you take the tool out and the button is not completely secured, just put it back in and press down again. *TIP* I often use a flat piece of wood to apply pressure, again to save my fingers. It also helps to avoid the button back going in at an angle.

8.  When you take the small assembly tool piece off, the fabric edges will be secured underneath the button back.

9.  Remove the button from the larger assembly tool piece.

10.  Tada! Now to attach it to the Clothespin.

11.  Use Hot Glue or E6000 to adhere a small plain button to the underside of the Cover Button. This is to fill the space between the back and the edges. You can also use felt or some other small object. You just need it to be sturdy enough to offer support. A small plastic button works great for this. You will see that the button is now flush across the bottom. I cut off the little nubs of glue that leaked through the button holes.

12.  Now adhere the finished Cover Button to the Clothespin. Press into place and center it until you are pleased with the alignment. Set aside to dry.

13. Tada! Additional uses:

  • Add a thin magnet to the back and use on your magnetic board.
  • Add a push pin to the back and use on your cork board.

To see other great Fabric Cover Button ideas, visit our DIY Project section here.

© ILikeBigButtons.com and I Like Big Buttons Blog, 2017.

Save

Save

I Like Big Buttons! Happy Easter!!! – Rainbow Spectrum KAM Snap Starter Pack Giveaway!!!

Easter Giveaway!!! As we prepare for another wonderful Easter with our family, we are running a great giveaway. Who wants to win a KAM Snaps Rainbow Spectrum Starter Pack Kit (100 Sets)!!!  Our KAM Snap Starter Pack would be a great tool for those crafty projects you have planned or a great gift for your crafty loved one :). 

Giveaway good until Monday 04/17/2017

ENTER TO WIN HERE (by Liking, Commenting, and Sharing our Facebook Post for this Giveaway):

a Rafflecopter giveaway

Giveaway Rules:

1. LIKE & SHARE this Giveaway, then COMMENT and share with us your favorite thing about Easter. – I love family time, the memories of past Easters, and watching my children create their own with their cousins, aunts, uncles, grandparents, and us. But above all that, I love the Hope that Easter represents! “He is risen!” Happy Easter to all!

2. Join our I Like Big Buttons! Group.

*If your name is drawn as the winner, we will check to make sure you have completed all 3 requirements above.

Also, if you don’t want to wait, you can get 10% off our Starter Packs and Pliers on our website.

Starter Pack (100 Sets) (18 Packs to choose from) Coupon Code: STARTER100

Starter Pack Snaps

Super Starter Pack (250 Sets) (15 Packs to choose from) Coupon Code: STARTER250

IMG_6519

© ILikeBigButtons.com and I Like Big Buttons Blog, 2017.

Save

Save

I Like Big Buttons! Happy Birthday To Me Sale!!!

It’s my Birthday weekend!!! I plan to sleep in, eat chocolate, and get almost nothing done while enjoying my family:). While I am busy completing my Birthday Bucket-list, enjoy this quick sale and celebrate with me.

Coupon Codes (Good through Monday 4/3/17 on our website):

HAPPYBDAY5  for 5% off of orders over $25

HAPPYBDAY7 for 7% off of orders over $50

HAPPYBDAY10 for 10% off of orders over $100

HAPPYBDAY15 for 15% off of orders over $200

***BONUS: Don’t forget that US orders over $70 also get upgraded to free shipping!!!

Happy Birthday to ME!!! Have a great crafty weekend!!!

I Like Big Buttons! and All Buttons big and small 🙂

KAM Snaps:

Pacifier Supplies:

All Enamel Clips Angle wide

Cover Buttons:

Key Fob Hardware:

Barrettes:

Bobby Pins:

Paper Clips:

Earring Supplies:

Sewing Clips:

Wonderific Clips All Main Shot

And Much More…

© ILikeBigButtons.com and I Like Big Buttons Blog, 2017.